CEI 211-6 PDF

Questa Norma viene pubblicata dal CEI nella sola lingua inglese in quanto particolarmente mirata a settori specialistici. La presente CEI image The Biodry device is in conformity with the safety requirements regarding exposition to electromagnetical fields, EN; ICNIRP, //CE, CEI 6. Control by local Authorities by using standards CE and and Article 14 of Law No. 36 a. b. Reference to Standard CEI Multiple frequency.

Author: Dasida Toramar
Country: Croatia
Language: English (Spanish)
Genre: Music
Published (Last): 26 April 2007
Pages: 497
PDF File Size: 16.93 Mb
ePub File Size: 13.21 Mb
ISBN: 872-5-80870-451-6
Downloads: 7740
Price: Free* [*Free Regsitration Required]
Uploader: Tygotaur

This part of IEC relates to the immunity requirements and test methods for electrical and electronic equipment, under operational conditions, to non-repetitive damped oscillatory transients ring waves occurring in low-voltage power, control and signal lines supplied by public and non-public networks.

GIRDINIO Paola

The effects of electromagnetic phenomena relating to the safety of apparatus are excluded from the scope of this standard. Immunity requirements in the frequency range 0 Hz to GHz are covered. No tests need csi be performed at frequencies where no requirements are specified. However, in the frequency range from kHz up to approximately 10 MHz protection from both, low frequency cel on the nervous system as well as high frequency effects need to be considered depending on exposure conditions.

The significant technical changes with respect to the previous edition are: Questa Norma viene pubblicata dal CEI nella sola lingua inglese in quanto particolarmente mirata a settori specialistici. The 21-6 practice covers the origin of surge voltages, rate of occurrence and voltage levels in unprotected circuits, waveshapes of representative surge voltages, energy, and source and impedance. Establishes a common and reproducible basis for testing electrical and electronic equipment when subjected to voltage dips, short interruptions or voltage variations on d.

Conformity with this standard can also be determined by validated simulations.

Biodry Technology | Soluzione umidità risalita |

The assessment consists of the induced current density for frequencies from 20 kHz to 10 MHz and the specific absorption rate SAR for frequencies from kHz to MHz around lighting equipment.

It forms a technical revision. This second edition cancels and replaces the first edition published in and constitutes a technical revision. Characteristics, performance and verification of the test generator and related inductive coils are revised. 211-66

It assists in meeting the requirements of IMO resolution A. The environments encompassed by this standard are industrial, both indoor and outdoor.

This second edition cancels and replaces the first edition published in and its Amendment 1 A practical basis is provided for the selection of voltage and current tests to be applied in evaluating the surge withstand capability of equipment connected to utility power circuits, primarily in residential, commercial, and light industrial applications. The test method documented in this part of IEC describes a consistent method to assess the immunity of an equipment or system against a defined phenomenon.

  CARTEA CALATORIA DE BRANDON BAYS PDF

This part of CISPR 16 is designated a basic standard, which specifies the characteristics and calibration of the absorbing clamp for the measurement of radio disturbance power in the frequency range 30 MHz to 1 GHz. Procedures are given for the measurement of the levels of spurious signals generated by the ITE and limits are specified for the frequency range 9 kHz to GHz for both class A and class B equipment.

These structures can be further classified as one- two- or multi-port TEM waveguides. This second edition cancels and replaces the first edition, published 2116- This second edition cancels and replaces the first edition published inand its Amendments 1 and 2 However, no emission requirements apply unless formulated in this standard.

In addition, requirements are provided for specialized equipment for discontinuous disturbance measurements.

This standard is also intended to be applied by manufacturers and suppliers of components and equipment which are to be added and connected to the vehicle harness or to an on-board power connector after delivery of the vehicle. It specifies the limits of voltage changes produced by equipment tested under specified conditions.

It covers equipment installed in residential areas as well as industrial machinery, specifically csi dips and short interruptions for equipment connected ceu either 50 Hz or 60 Hz a. Equipment which fulfils the requirements at these frequencies is deemed to fulfil the requirements in the entire frequency range from 0 Hz to GHz for electromagnetic phenomena. The objectives of this publication are to establish requirements which provide an adequate level of protection of the radio spectrum, allowing radio services to operate as intended in the frequency range 9 kHz to GHz and to specify procedures to ensure the reproducibility of measurement and the repeatability of results.

Friest – Strumentazione per misure CEM, Strumentazione EMC e Filtri RF

This standard defines a range of: This third edition cancels and replaces the second edition published in The applicability of IEC La presente Norma ha lo scopo di definire i limiti e i metodi di prova per le apparecchiature elettriche ed elettroniche da utilizzare negli ambienti industriali, in relazione alle emissioni elettromagnetiche, che possono causare interferenze ad altre apparecchiature, nella gamma di frequenze da 0 a GHz e per le quali non esistono norme sull’emissione riferite al prodotto o a famiglie di prodotti.

  GLOMERULONEFRITIS POSTESTREPTOCOCICA FISIOPATOLOGIA PDF

La presente Norma riporta il testo in inglese e italiano della EN ; rispetto al precedente fascicolo n. It includes the following significant technical changes with respect to the previous edition: Questa Norma non fornisce misure protettive per persone che abbiano impiantati dispositivi medici attivi. The Biodry technology reverse the current flow which carries the molecules of water up, simply disconnecting the electrical interference on walls.

This consolidated version consists of the first editionits amendment 1 and its amendment 2 This standard applies also to apparatus which is battery operated or is powered by a non-public, but non-industrial, low-voltage power distribution system if this apparatus is intended to be used in the locations described below. The test requirements are specified for each port considered.

The object of this basic standard is to establish the immunity requirements and a common reference for evaluating in a laboratory the performance of electrical and electronic equipment intended for residential, commercial and industrial applications, as well as of equipment intended for power stations and substations, as applicable.

The frequency range covered extends from 9 kHz to GHz. Aiutaci ad esserti d’aiuto! These requirements represent essential electromagnetic compatibility emission requirements.

It specifies the immunity requirements in relation to continuous and transient, conducted and radiated electromagnetic disturbances, including electrostatic discharges, for the above-mentioned apparatus. Test conditions for particular equipment are given in Annex C. These health criteria have provided the scientific database for the subsequent development of exposure limits and codes of practice relating to NIR.

Biodry the Solution

The specifications in this standard apply to EMI receivers and spectrum analyzers. Le prescrizioni per le prove in situ sono allo studio. Eco-Friendly The Biodry technology reverse the current flow which carries the molecules of water up, simply disconnecting the electrical interference on walls.

Tali informazioni riguardano essenzialmente: The existing dump turn back to the ground in an absolutely natural way, favoring the definitive drying up of walls.

This collateral standard to IEC specifies general requirements and tests for basic safety and essential performance with regard to electromagnetic disturbances and for electromagnetic emissions of ME equipment and ME systems.